Before running airodump-ng, you may start the script to list the detected wireless interfaces. It is possible, but not recommended, to run and airodump-ng at the same time. Airodump-ng will display a list of detected access points, and also a list of connected clients (“stations”). Futurmat Ariete F3 Manual. Here's an example screenshot: CH 9 ][ Elapsed: 1 min ][ 2007-04-26 17:41 ][ WPA handshake: 00:14:6C:7E:40:80 BSSID PWR RXQ Beacons #Data, #/s CH MB ENC CIPHER AUTH ESSID 00:09:5B:1C:AA:1D 11 16 10 0 0 11 54.

Peek Dll Peek5 Sys And Msvcr70 Dll Descargar ->>>DOWNLOAD Description Descargar aircrack ng 0 9 3 Aircrack-ng-0.9.3-win.zip descargar. Aircrack-ng is a complete suite of tools to assess WiFi network..

OPN NETGEAR 00:14:6C:7A:41:81 34 100 57 14 1 9 11e WEP WEP bigbear 00:14:6C:7E:40:80 32 100 752 73 2 9 54 WPA TKIP PSK teddy BSSID STATION PWR Rate Lost Packets Probes 00:14:6C:7A:41:81 00:0F:B5:32:31:31 51 36-24 2 14 (not associated) 00:14:A4:3F:8D:13 19 0-0 0 4 mossy 00:14:6C:7A:41:81 00:0C:41:52:D1:D1 -1 36-36 0 5 00:14:6C:7E:40:80 00:0F:B5:FD:FB:C2 35 54-54 0 99 teddy The first line shows the current channel, elapsed running time, current date and optionally if a WPA/WPA2 handshake was detected. In the example above, “WPA handshake: 00:14:6C:7E:40:80” indicates that a WPA/WPA2 handshake was successfully captured for the BSSID. In the example above the client rate of “36-24” means: •. Field Description BSSID MAC address of the access point. In the Client section, a BSSID of “(not associated)” means that the client is not associated with any AP.

In this unassociated state, it is searching for an AP to connect with. PWR Signal level reported by the card. Its signification depends on the driver, but as the signal gets higher you get closer to the AP or the station. If the BSSID PWR is -1, then the driver doesn't support signal level reporting. If the PWR is -1 for a limited number of stations then this is for a packet which came from the AP to the client but the client transmissions are out of range for your card.

Meaning you are hearing only 1/2 of the communication. If all clients have PWR as -1 then the driver doesn't support signal level reporting. RXQ Receive Quality as measured by the percentage of packets (management and data frames) successfully received over the last 10 seconds. See note below for a more detailed explanation. Beacons Number of announcements packets sent by the AP.

Each access point sends about ten beacons per second at the lowest rate (1M), so they can usually be picked up from very far. # Data Number of captured data packets (if WEP, unique IV count), including data broadcast packets. #/s Number of data packets per second measure over the last 10 seconds. CH Channel number (taken from beacon packets). Download Mediafour Macdrive 8.0.3.2 Inc Keymaker on this page. Note: sometimes packets from other channels are captured even if airodump-ng is not hopping, because of radio interference. MB Maximum speed supported by the AP.

If MB = 11, it's 802.11b, if MB = 22 it's 802.11b+ and higher rates are 802.11g. The dot (after 54 above) indicates short preamble is supported. Displays “e” following the MB speed value if the network has QoS enabled.

ENC Encryption algorithm in use. OPN = no encryption,“WEP?” = WEP or higher (not enough data to choose between WEP and WPA/WPA2), WEP (without the question mark) indicates static or dynamic WEP, and WPA or WPA2 if TKIP or CCMP is present. CIPHER The cipher detected. One of CCMP, WRAP, TKIP, WEP, WEP40, or WEP104. Simearth Manual. Not mandatory, but TKIP is typically used with WPA and CCMP is typically used with WPA2.